It’s the PETG. Specifically, it is the softening on the following parts:
I would recommend the following Y-axis mod for the MK4. I am still running this even on the MK4S, even though the Y-axis was modified on the MK4S.
Edit: Print those in ASA and replace them, tighten all the belts as usual, and I think your printer will be fixed.
My money is on the PETG starting to loosen and you losing tension on the belts.
You have the MK4 in an enclosure–I did too. At some point I stopped being able to print flexibles, but ASA/PCCF was still fine. Prusa support told me that the idler was getting loose and my hotend was losing grip on the fillament.
I had another print where there was a nearly 2-3cm shift in the layers between layer 5 and layer 80. Some of my belts had absolutely lost the plot. I reprinted everything in ASA or PCCF, and while upgrading to the MK4S rebuilt the printer with all ASA/PCCF parts. No problems since.
Non mais, c’est quoi ce langage alarmiste?
C’est quoi le but exactement? De faire croire aux gens que les airbags sont plus dangereux que… checks notes… s’exploser le crâne sur le volant, en cas d’impact?
Voici une page avec plus d’infos: https://www.ecologie.gouv.fr/rappel-airbag-takata
I’m someone who builds cloud infrastructure for a living. I only touch AWS (Amazon), but the same applies to Azure (Microsoft) and GCP (Google).
Kagi is private. Saying that they “rely” on Google because they use GCP is akin to saying that the US Army relies on General Motors because they use Hummers. It’s just a provider. They’re renting virtual machines, compute power, storage, and network bandwidth nothing more. You can use GCP/Azure/AWS without your data ever being visible by GCP/Azure/AWS. It’s not because you use GCP that you have to use AdSense/Analytics/Fonts, etc. They are completely separate.
Politicians would have a field day with all the cloud providers if using one thing forced you to use everything.
It could be a case of too much cooling, while simultaneously being too much heat.
If you’re blowing so much air that the filament instantly solidifies when it leaves the nozzle, it’s not going to bond with anything else. It’s also interesting that the first layers are fine (when the part cooling fan is typically not running), but problems start when the part cooling fan turns on.
Have you tried without part cooling at all? Another thing is that your part cooling might be cooling down the tip of the nozzle, causing tiny partial clogs, which are cleared every so often by friction.
Did you notice a difference in print speed when you slowed down? As this is a small print, it could already be as slow as it will be due to minimum layer times.
It could also be that the nozzle spends too much close to the print. What happens if you print 2 or 3 of them?
This is typically more of an issue with PC where you don’t have a part cooling fan running, but maybe it’s the case here too?
Definitely doesn’t sound like an issue with Tor Browser in Strict Mode. /s
The simple fact that buying a $300 device and to “not expect software updates” is not considered a scam is hilarious to me.
Interesting that the extra 10° makes such a difference for ASA and ABS.
I recently started printing with ASA in my enclosed MK4. I might have to try this.
Soit tout le monde a un vote, soit personne n’en a. Limiter la participation c’est créer des non-citoyens, et on a vu ce que ça donne.
Là où il faut intervenir c’est sur la participation. 51% à l’échelle européenne. 51.5% en France. La Belgique fait la fière avec ses 90% de participation, mais ça ne suffit pas. En Croatie 4 personnes sur cinq se sont abstenues. Bon nombre de pays où c’est 2 sur 3.
Perpignan est géologiquement dans une cuve de pierre, avec très peu d’entrées naturelles. Les POs n’ont que 40% du terrain qui est “sédimentaire”, et qui peut donc absorber l’eau de pluie. L’Agly, le Réart, la Tet et le Tech sont régulièrement a sec, je me souviens faire du camping dans le Réart il y a 20 ans.
La surface sédimentaire est très argileuse, ce qui veut dire que c’est un sol qui est incapable d’absorber de l’eau. Quand c’est sec, rien ne pénètre, et quand c’est saturé, rien ne pénètre. L’eau de pluie finit dans la Méditerranée.
Si tu superposes la carte page 19 du PDF et la carte page 16, tu vois que la majorité du terrain qui n’est pas de la roche pure c’est de l’argile. RIP.
You didn’t get laid off because you discussed your wages.
You were laid off because you couldn’t keep your cards close to your chest and told the company y’all had been discussing wages.
Having the right to discuss it doesn’t mean you should do it in front of the boss.
In Denmark, I’m part of a union which publishes salary stats for every possible job title, management responsibility, education, in a fairly convoluted matrix. Still, this allows me to easily negotiate with companies and see how well they pay. There might be something organised by the government, but I’ve never had a need for it.
Germany has a principle of equal treatment. The only way to ensure this is respected is to discuss wages. There is a legal precedent that makes it completely unambiguous that discussing wages is protected. It may be uncomfortable, but that’s just social pressure, encouraged by companies.
You cannot prevent your employees from discussing wages. It is literally illegal to do so, and you cannot reprimand people for doing so.
Under the National Labor Relations Act (NLRA or the Act), employees have the right to communicate with their coworkers about their wages, as well as with labor organizations, worker centers, the media, and the public. Wages are a vital term and condition of employment, and discussions of wages are often preliminary to organizing or other actions for mutual aid or protection.
If you are an employee covered by the Act, you may discuss wages in face-to-face conversations, over the phone, and in written messages. Policies that specifically prohibit the discussion of wages are unlawful as are policies that chill employees from discussing their wages.
You may have discussions about wages when not at work, when you are on break, and even during work if employees are permitted to have other non-work conversations. You have these rights whether or not you are represented by a union.
https://www.nlrb.gov/about-nlrb/rights-we-protect/your-rights/your-rights-to-discuss-wages
Je ne suis ni petit, ni néo, ni lib :).
Perso, je ne pensais pas que le terme que j’avais utilisé était si insultant que ça. C’était pour moi plus une façon d’indiquer qu’il y avait un manque de perspective.
J’ai édité mon commentaire, j’espère que mon point de vue est plus clair. Pour info j’ai vécu quelques temps à Kyiv et j’ai perdu un bon nombre d’amis dans ce conflit, d’où mon point de vue biaisé.
Bon weekend
J’ai revu mon commentaire pour être moins provocateur/agressif. Mes excuses.
Il ne faut pas tout mélanger. Protéger l’Ukraine, c’est protéger l’intégrité de l’Europe. Je ne parle pas de l’UE, mais de l’Europe d’un point de vue géographique. Si on tolère que la Russie envahisse nos frontières, on va devoir faire face à une nouvelle catégorie de problèmes, pour lesquels on n’a franchement pas le temps, ni les ressources. Vous pensez qu’on va “finir en cendres” si on les oppose maintenant? Que va-t-il se produire lorsqu’ils auront réétabli un bloc similaire à celui de l’aire Soviétique? À mon sens, il manque un peu de réflexion sur les effets long-termes pour tenir ce genre de propos.
Il n’est pas possible de dire que Macron et le FN sont les suppléants de la Russie, et du même revers rejetter sa proposition d’une intervention anti-Russe en Ukraine. Soit c’est un pion de poutine, soit il ne l’est pas.
Aussi, stop le spam. En 30 minutes t’as posté 5 articles dont 3 du même site.
Pedantic moment: “every business’ focus”, or “all businesses’ focus”, but not “every businesses’ focus”.
Not sure what you need to get approved. Buying a roll of ASA? It’s part of printer maintenance, and making it more reliable in the long run.
And if you don’t have ABS/ASA on hand… why is the printer in an enclosure?